A great multi-use starter/charger with amp rates for fast emergency starts, regular charging needs and trickle charging small batteries. For 6 and 12 volt batteries. • 50 amp engine start – for emergency starting. • 10 amp fast charge – for everyday charging needs. Charges in 3 to 5 hours. • 2 amp trickle charge – charges a small 12 volt battery in 2 to 12 hours. • 2 LED lights – signal Power On and Fully Charged. • Automatic shut off – will not overcharge batteries. • Convenient carrying handle.Learn More
Regular Price: $89.99
Special Price: $79.99
Keep you car’s air conditioner cool all summer long with this value-size 30lb cylinder of Freon R134/R134a Refrigerant. The large size will save you time and money. Instead of purchasing several small cans of Freon, just one of these 30lb cylinders will allow for multiple recharges. This product is for use in retrofitted and/or factory installed R134a auto air conditioning units. Standard ACME threaded cap is included. Meets ARI 700 regulations, and is compliant for use in California.
Expedited shipping not available for this product. Can only be shipped via UPS Ground or Freight.
- Part number: 6330
- Unit UPC: 39101063300
- Unit weight: 36.25lb
- Content weight: 30lb.
- Flash point: NAGas
- Boiling point: -15.5°F
- Specific gravity: 1.21
- Propellant: not applicable
- Clear, colorless liquid/vapor
- Ether-like odor
- Low flammability
- Plastic safe
- VOC%: not determined
- VOC category: not applicable
- Compliant for CA
12 PACK of Cans
Application Temperature Range
R-134a performance suffers at lower evaporator temperatures. In general it is not applied at temperatures below -10F, and it is not necessarily the most economical overall choice in some other applications. Traditional R-12 type applications have adopted several products as alternatives, including R-134a, R-22, R-404A/R-507, and numerousretrofit blends.
R-134a requires polyol ester (POE) lubricants, primarily for their ability to mix with HFC refrigerants. Traditional mineral oils and alkylbenzene do not mix with HFCs and will cause compressor failures. In addition, automotive air conditioning systems may also use polyalkaline glycol (PAG) lubricants (not typically seen in stationary equipment). Both POEs and PAGs will absorb moisture, and hold onto it, to a much greater extent than traditional lubricants. The moisture will promote reactions in the lubricant as well as the usual problems associated with water (corrosion, acid formation, etc.). The best way to dry a wet HFC system is to use a filter drier - run the system and change the drier - instead of relying on evacuation to clear the water.
Equipment built for R-12 will be sized a bit too small compared to equipment built for R-134a. In order to do the same job an R-134a system will need a larger compressor and larger heat exchangers. As a result a system which is retrofit from R-12 to R-134a will have lower capacity (run longer) and will probably develop higher head pressures (not enough condenser area). The lubricant will also need to be flushed and replaced with POE (residual mineral oil content less than 5%).
This product cannot go expedited shipping, must go ground.Learn More
Why Switch from the Traditional R22 Refrigerants
Frost 22a Refrigerant Replaces R22 Substitutes
Frost 22a is sold as a second generation replacement for R407c, R404a and MO99.
- Do it Yourself!
- No license Required
- Use up to 40% less
- Lower operating costs
- Less heaed pressure, extremely efficient
- Non-ozone depleting product
- Non-Toxic, Non-Carcinogen - No Long Term health Risks
- Compatible with Mineral & Synthetic (Ester & Pag) Lubricants
- Proven Results
- Classified as Pharmaceutical Grade
- Government phasing out traditional R22
- Made in USA
- Hydro Carbon Leak Detector is recommended for checking Leaks (Leak Detector Not Included)
*This product is equaivalent to 30 lbs of traditional R-22. Because this is a lighter gas you will only need to use 1oz of 22A for every 2.5oz you had to use with traditional R-22.
This product cannot go expedited shipping, must go UPS Ground or Freight.
Guidelines for the Pressure of 22A
Charge low side pressure to around 70 PSI. Your high side pressure should be around 230-250 PSI. Always fill from the low pressure side. It should be at about 40-44 degrees on the evaporator coil. Those are the ranges of a typical charge.Learn More