A great multi-use starter/charger with amp rates for fast emergency starts, regular charging needs and trickle charging small batteries. For 6 and 12 volt batteries. • 50 amp engine start – for emergency starting. • 10 amp fast charge – for everyday charging needs. Charges in 3 to 5 hours. • 2 amp trickle charge – charges a small 12 volt battery in 2 to 12 hours. • 2 LED lights – signal Power On and Fully Charged. • Automatic shut off – will not overcharge batteries. • Convenient carrying handle.Learn More
Regular Price: $6.99
Special Price: $5.99
Don't get caught in a hot vehicle with a broken air conditioner! The last thing you need is to show up and work or social functions wet with sweat and body odor. Prepare ahead of time by checking your fluids in your automobile and using R134a Air Conditioning to keep it cool and running smooth. Easy to use, easy to apply, leaving you with a cool and easy ride!
- With a boiling point of -15.5 degrees Fahrenheit, specific gravity at 1.21 and low Flammability, R134a has clear, colorless liquid vapors.
- Performance declines at temperatures below -10°F (-26.4° C)
- Freezing point -160° C
- Unit Weight 15.5 oz
- Fill Weight 12 oz
- Requires Polyol Ester Lubricants
- Keep out of reach of children.
This product cannot go expedited shipping, must go ground.
Regular Price: $89.99
Special Price: $79.99
Keep you car’s air conditioner cool all summer long with this value-size 30lb cylinder of Freon R134/R134a Refrigerant. The large size will save you time and money. Instead of purchasing several small cans of Freon, just one of these 30lb cylinders will allow for multiple recharges. This product is for use in retrofitted and/or factory installed R134a auto air conditioning units. Standard ACME threaded cap is included. Meets ARI 700 regulations, and is compliant for use in California.
Expedited shipping not available for this product. Can only be shipped via UPS Ground or Freight.
- Part number: 6330
- Unit UPC: 39101063300
- Unit weight: 36.25lb
- Content weight: 30lb.
- Flash point: NAGas
- Boiling point: -15.5°F
- Specific gravity: 1.21
- Propellant: not applicable
- Clear, colorless liquid/vapor
- Ether-like odor
- Low flammability
- Plastic safe
- VOC%: not determined
- VOC category: not applicable
- Compliant for CA
This Ideal Division-stant 1-.31in. To 2-.25in. Trim-Gear Hose ClampsLearn More
12 PACK of Cans
Application Temperature Range
R-134a performance suffers at lower evaporator temperatures. In general it is not applied at temperatures below -10F, and it is not necessarily the most economical overall choice in some other applications. Traditional R-12 type applications have adopted several products as alternatives, including R-134a, R-22, R-404A/R-507, and numerousretrofit blends.
R-134a requires polyol ester (POE) lubricants, primarily for their ability to mix with HFC refrigerants. Traditional mineral oils and alkylbenzene do not mix with HFCs and will cause compressor failures. In addition, automotive air conditioning systems may also use polyalkaline glycol (PAG) lubricants (not typically seen in stationary equipment). Both POEs and PAGs will absorb moisture, and hold onto it, to a much greater extent than traditional lubricants. The moisture will promote reactions in the lubricant as well as the usual problems associated with water (corrosion, acid formation, etc.). The best way to dry a wet HFC system is to use a filter drier - run the system and change the drier - instead of relying on evacuation to clear the water.
Equipment built for R-12 will be sized a bit too small compared to equipment built for R-134a. In order to do the same job an R-134a system will need a larger compressor and larger heat exchangers. As a result a system which is retrofit from R-12 to R-134a will have lower capacity (run longer) and will probably develop higher head pressures (not enough condenser area). The lubricant will also need to be flushed and replaced with POE (residual mineral oil content less than 5%).
This product cannot go expedited shipping, must go ground.Learn More