Fluids - Lubricants
Regular Price: $89.99
Special Price: $79.99
Keep you car’s air conditioner cool all summer long with this value-size 30lb cylinder of R134/R134a Refrigerant. The large size will save you time and money. Instead of purchasing several small cans of refrigerant, just one of these 30lb cylinders will allow for multiple recharges. This product is for use in retrofitted and/or factory installed R134a auto air conditioning units. Standard ACME threaded cap is included. Meets ARI 700 regulations, and is compliant for use in California.
Expedited shipping not available for this product. Can only be shipped via UPS Ground or Freight.
- Part number: 6330
- Unit UPC: 39101063300
- Unit weight: 36.25lb
- Content weight: 30lb.
- Flash point: NAGas
- Boiling point: -15.5°F
- Specific gravity: 1.21
- Propellant: not applicable
- Clear, colorless liquid/vapor
- Ether-like odor
- Low flammability
- Plastic safe
- VOC%: not determined
- VOC category: not applicable
- Compliant for CA
12 PACK of Cans
Application Temperature Range
R-134a performance suffers at lower evaporator temperatures. In general it is not applied at temperatures below -10F, and it is not necessarily the most economical overall choice in some other applications. Traditional R-12 type applications have adopted several products as alternatives, including R-134a, R-22, R-404A/R-507, and numerousretrofit blends.
R-134a requires polyol ester (POE) lubricants, primarily for their ability to mix with HFC refrigerants. Traditional mineral oils and alkylbenzene do not mix with HFCs and will cause compressor failures. In addition, automotive air conditioning systems may also use polyalkaline glycol (PAG) lubricants (not typically seen in stationary equipment). Both POEs and PAGs will absorb moisture, and hold onto it, to a much greater extent than traditional lubricants. The moisture will promote reactions in the lubricant as well as the usual problems associated with water (corrosion, acid formation, etc.). The best way to dry a wet HFC system is to use a filter drier - run the system and change the drier - instead of relying on evacuation to clear the water.
Equipment built for R-12 will be sized a bit too small compared to equipment built for R-134a. In order to do the same job an R-134a system will need a larger compressor and larger heat exchangers. As a result a system which is retrofit from R-12 to R-134a will have lower capacity (run longer) and will probably develop higher head pressures (not enough condenser area). The lubricant will also need to be flushed and replaced with POE (residual mineral oil content less than 5%).
This product cannot go expedited shipping, must go ground.Learn More
Mobil Delvac 1300 Super 15W-40 is an extra high performance diesel engine oil that helps extend engine life and drain intervals in the most severe on and off-highway applications. The advanced chemistry of this product delivers exceptional performance in both modern high-output, low-emission engines including those with Exhaust Gas Recirculation (EGR) as well as older engines operating on low or higher sulfur fuel. As a result, this product meets or exceeds the new API CI-4 service category and JASO industry specifications. Mobil Delvac 1300 Super 15W-40 is recommended for use in a wide range of heavy-duty applications and operating environments found in the trucking, mining, construction, quarrying, and agricultural industries. This product also meets the latest API specifications for gasoline engines and mixed fleets. The outstanding performance reserve of Mobil Delvac 1300 Super 15W-40 is the result of extensive cooperative development work with major OEMs and advanced additive chemistry with patented Trimer technology. These enhancements assure excellent control of oil thickening due to soot buildup and exposure to higher temperatures and provide outstanding resistance to oxidation, corrosion, wear, and high temperature deposits. Due to its unique formulation, it also meets the more demanding SAE 10W cold temperature pumping requirements.Learn More
Specially formulated EnduraPlas diesel grade polyethylene fuel transfer tank provides a hasslefree, completely assembled option for transporting diesel fuel. Features a built-in 10 GPM pump with on/off switch and integrated bypass valve. U.S.A.
- (1) 100-gal. diesel fuel transfer tank with 10 GPM pump
- (1) 15ft. hose
- (1) Auto shutoff nozzle
- Strong, lockable poly lid protects the pump compartment and reduces fuel theft
- Durable, corrosion-resistant polyethylene construction
- Includes 15ft. of 3/4in. hose with an anti-kink spring and swivel to prevent tangles
- Easy-to-clean suction strainer and splash-resistant breather installed
- 3/4in. auto shutoff nozzle adds convenience
- Molded-in plastic handles for easy maneuvering and tank relocation
- Bottom drain plug on tank allows for complete drainage when desired
Features Tank Type Transport Mounting Type Strap, bolt Tank Size (gal.) 100 Shape Square Dimensions L x W x H (in.) 48 x 34 x 29 Outlet Diameter (in.) 3/4 Inlet Diameter (in.) 2 Finish Type Poly
In order to meet the demands of EPA2010 standards, commercial vehicle manufacturers have evaluated various engine technologies that will provide low emissions and increased performance. SCR technology or Selective Catalytic Reduction is the option many engine and truck manufacturers have chosen. In simple terms, a fine mist of emission fluid is dosed into the exhaust that reacts and neutralizes the NOx molecules. A separate tank is fitted on the SCR truck to house the emission fluid. The rate of consumption for the fluid is 2 to 4% per gallon of diesel fuel. Manufacturers estimate that refueling the emissions tank will occur every other diesel fuel fill up.Learn More
Your oil needs to work harder than ever where higher temperatures, higher soot loading and the requirement for lower exhaust emissions are a fact of life. Shell Rotella T has been formulated to provide Triple Protection against wear, deposits and emissions to help you and your business benefit from long engine life and lower operating cost.Learn More
BriskHeat’s Drum / Pail Warmer is a great solution to prevent drum and pail contents from freezing. The warmer helps maintain elevated temperatures, enabling contents to flow even when ambient temperatures drop as low as 0°F. The built-in thermostat keeps the materials in the drum warm between 67° to 85°F. BriskHeat Corporation has been producing high quality and industrial grade drum and pail warmers for the past 64 years, providing users with unmatchable durability
- Portable plug-and-play design
- Can be used on metal or plastic drums and pails
- Suitable for both outdoor and indoor uses
- Moisture and chemical resistant
- Effective in ambient temperature as low as 0°F
- Extra-wide 4” heater coverage with stretchable spring fastener
- Available in variety of sizes: 5, 15, 30 and 55 gallons
Specifications Voltage: 120VAC Thermostat: Built-in, self-regulates between 67° (+/-9°F) to 85°F (+/-5°F) Power cord: 6-foot power cord with standard 3-prong wall plug Grounded for safety: Patented 360°grounded heating element Watt density: 4 watts/sq in Wattage: 700 Drum Diameter: 14 in. Warmer Length: 44 in. Warmer Width: 4 in.
- Freeze Protection
- Warming contents of drums and pails
- Preventing Chemical Separation or Crystallization
- Keeping paint warm
BriskHeat’s XtremeFLEX® Emergency De-Icer is for rapid-de-icing, thawing,temperature control, and emergency supplemental heat. It is used on metal pipes, valves, pumps, and other metal surfaces. Since 1949, BriskHeat Corporation has been THE trusted source for heating applications.
Rugged construction for unsurpassed durability
- De-Icing Pipes
- Thawing Valves
- Warming Pumps
- Improving Cold Weather-Related Flow Problems
- Portable plug-and-play, ready-to-install design
- Rapid heating: 10X heating output of a typical water pipe freeze protection
- Exceptional flexibility - Wraps around metal surfaces as small as 1/2” diameter
- 1” wide moisture and chemical resistant heat tape
- Available in variety of lengths: 2 ft, 6 ft and 10 ft
Controller: Built-in, adjustable between 50°to 160°F
Power cord: 120VAC with 6-foot power cord with standard 2-prong wall plug
Watt density: 6 watts/sq in
Specifications Voltage: 120VAC Controller: Built-in, adjustable between 50°to 160°F Power cord: 120VAC with 6-foot power cord with standard 2-prong wall plug Watt density: 6 watts/sq in Wattage: 432 Dimensions: 1" x 6"
1 year warrantyLearn More
RV Antifreeze protects from freezing down -50º Fahrenheit. There is no mixing of the antifreeze. This antifreeze is non-toxic and tasteless. Use 1 gallon for small units with no tanks, appoximatly 2 gallons for units under 18 feet, use 3 gallons for 18 - 20 feet long. Use 3 or more gallons in cabins. Safe for all pool surfaces including copper, brass, plastic, but not acetate.
- Recreational Vehicle
- Swiming Pools
- vacation Homes
Not for use in enginesLearn More