250 Psi Rubber Air Hose : Solid brass end fittings: 1/4-inch NPT. Spiral synthetic yarn reinforcement. Abrasion-resistant rubber outer jacket. 100 Percent made and assembled in the USA. Technical Specifications: 250 PSI working pressure, exceeds RMA 4:1 safety factor (burst pressure to working pressure ratio), meets RMA Class "C" oil resistance, working temperature range: -40 to 190-degrees F.Learn More
A light to medium penetrating all-purpose stick electrode for use in all positions, on carbon steel. Runs on AC or DCEP (reverse) polarity or DCEN (straight) polarity. 60,000 PSI tensile strength. Good for general, all-purpose applications and joints with poor fit-up.
- Size: 1/8".
- 1lb Plastic.
Kit consists of one hex key wrench, one blade clamp and one blade clamp screw for keyed spindle standard Sawzall® modelsLearn More
KwikWood is a hand-mixable epoxy putty, formulated to repair and rebuild wood. After mixing, it cures to the same density as wood and becomes an integral part of the repair. For use on exterior or interior applications, it contains no solvents, will not rot, shrink, crack or pull away. KwikWood has a 15-25 minute work life. After 60 minutes, it can be machined, drilled, tapped, sanded, filed and painted. Stronger than wood, KwikWood dries to a light tan color.
- Cut: Remove required amount of putty.
- Mix: Thoroughly knead putty with fingers to a uniform color.
- Apply: Press putty firmly to the surface to be repaired.
- Dry Rot
- Knot Holes
- Window & Door Frames
- Screw Holes
- Insect Damage
- Furniture & Carvings
- Gouges & Cracks
- PVC Trim Board
- Strength 900 PSI
- Set Time 15-25 Minutes
- Cure Time 1 Hour
- Cure Color Light Tan
* For best results use a detergent or degreaser to first clean the surface, then roughen surface with file or coarse sandpaper to provide the best repair. STAINING: KwikWood accepts stain differently from wood. Some types of pigments and colorants may be added during the mixing step. Always test for stain acceptance, color match and hardening before application.Learn More
WATERWELD will plug or seal practically anything that leaks. It will patch holes and cracks, and mend almost anything that is broken. It is excellent for rebuilding or fabricating parts, and as an all-purpose adhesive for metals, wood, fiberglass, masonry, ceramics, PVC and ABS. Permanently repair holes, gouges, cuts ... even seals rot in fiberglass and wood. Cures under water. Safe for use on lines carrying potable water. We should really call this amazing product "The Miracle Welder," because you can use it to plug holes and make permanent repairs under water and in gas tanks -- while they're still leaking. No exaggeration -- this is the best epoxy putty you can use.
How Does It Work?
WATERWELD can be applied under water; surfaces to be repaired do not need to be clean and dry. WATERWELD putty "mushrooms" through and around holes, grabbing the edges to hold securely, then hardening for a permanent seal.
WATERWELD is approved by the National Sanitation Foundation for use with potable water (meaning you can drink safely from fresh water pipes or utinsels repaired with it).
How to Use J-B Weld Water Weld
Use WATERWELD as an adhesive, laminate, plug, filler, sealant, and electrical insulator. Packaged in a single cylinder, you simply cut off as much of the material as you need, twist and knead with your fingers until color is uniform with no streaks, apply immediately to surface to be repaired, and remove excess with soap.
WATERWELD can be formed, drilled, ground, tapped, machined, filled, sanded, and painted. It stays pliable for about 2 minutes after mixing, sets in just 20 minutes, and cures fully in just a few hours. It's water-proof; petroleum-, chemical-, and acid-resistent; resists shock, vibration, and extreme temperature fluctuations, and withstands temperatures up to 300° F. WATERWELD is super strong, non-toxic, and safe to use. Before it sets, you can clean up with soap and water.
What Does It Bond To?
Virtually any combination of iron, steel, copper, aluminum, brass, bronze, pewter, porcelain, ceramic, marble, glass, PVC & ABS, concrete, fiberglass, wood, fabric, paper -- just about any porous and non-porous material.
- Titanium nitride coating extends the life of the bit; lasts up to six times longer than standard high speed steel drill bits
- Heavy-duty web design provides extreme rigidity when drilling in metal applications
- Shorter cutting lips reduce torque when drilling in high tensile strength materials
- 135-degree split point reduces feed pressure for easier penetration without work hardening