McAfee SECURE sites help keep you safe from identity theft, credit card fraud, spyware, spam, viruses and online scams



7AM - 5PM CST 7 Days a Week


Subscribe to receive members-only deals in your email





6 Item(s)

per page

Grid List

Set Ascending Direction
  1. Hobart AirForce 40i 230V Portable Air Plasma Cutter 500566

    Hobart AirForce 40i 230V Portable Air Plasma Cutter 500566


    Need to cut steel? Thinking about an oxy acetylene cutting torch to do the job? Consider a plasma cutter. This simple technology uses an electrical arc and compressed air to cut steel, aluminum, and other conductive metals.

    The AirForce 40i plasma cutter features an inverter design that is both lightweight and powerful. The product also features an ergonomic trigger safety, more efficient air consumption, and economically priced XT40R torch consumables. The 40i requires 230 V, 50 A input power and compressed air delivery of at least 4.8 scfm @ 90-120 psi. Maximum cutting of mild steel is 7/8 inch at 50% duty cycle for heavy-duty production requirements.

    Compared to the complexities of an oxy fuel cutting torch system, plasma cutting is easy.

    • Cuts faster than oxy fuel
    • More precise cut, thinner kerf, less slag to clean up
    • Smaller heat-affected zone for less warping
    • No gas pressure settings or flame tuning needed
    • No preheating of metal prior to cutting


    • XT40R Torch - Designed for increased comfort with an ergonomic trigger safety, more efficient cooling and economical replacement cutting tips.
    • Pilot Arc Controller - Allows you to cut expanded/perforated metals, as well as painted or coated surfaces, without retriggering the torch.
    • Wind Tunnel Technology - Prevents abrasive dust and particles from damaging internal components.
    • Fan-On-Demand - Cooling system operates only when needed reducing power consumption and contaminants drawn into the machine.
    • Power Factor Correction (PFC) Circuitry - Draws up to 30% less amperage for the same cutting range as compared to the competition. PFC expands operators work area via extension cord, while minimizing nuisance circuit breaker trips caused by voltage drops.
    • LVC Line Voltage Compensation - Provides peak performance power under variable input voltage conditions (±15%) for steady and cleaner-ending cuts.
    • Internal Gas/Air Filter and Regulator - Controls amount of usage and flow of air or gas.
    • Starts Without High Frequency - Protects unit by not interfering with or damaging controls or computers.
    • Diagnostic Lights - LED lights for quick troubleshooting of pressure, power and cup situations.
    • Cable Management Strap - Secures torch, work cable and power cord to make transporting easy and convenient.
    • Postflow Cooling Circuit - Extends life of consumables and torch by cooling them with postflow air after trigger is released.
    • Compatible with Engine-Driven Welders - Capable of cutting 3/8–5/8 in. mild steel when powered by an engine-driven welder with a 240 V generator power outlet of 8 kW or more.
    • Hobart's 5/3/1 Industrial Warranty - Five-year manufacturer warranty on transformers, stabilizers and generators; three years on electronics (drive motors, rectifiers); and one year on guns (MIG and plasma torches).

    Comes with:

    • 12-ft. (3.7 m) XT40R hand-held torch
    • 12-ft. (3.7 m) work cable with clamp
    • Extra consumables
    • 10-ft. (3 m) power cord with plug
    • Easy-to-connect, built-in gas/air filter and regulator for extra protection


    • Maintenance
    • Light Construction
    • Prototyping
    • Body Shops/Fabrication


    • Rated Output at 50% Duty Cycle: 40 A, at 140 VDC
    • Max. Open-Circuit Voltage: 400 V
    • Amps Input at Rated Output, 60 Hz: 208 V -33, 230 V 30
    • kVA: 6.8
    • kW: 6.6
    • Plasma Gas Flow/Pressure: 4.8 CFM (136 L/min) at 90 –120 PSI (621–827 kPA) Recommended
    • Dimensions:
      • H: 11-1/4 in. (286 mm)
      • W: 8-1/4 in. (210 mm)
      • D: 14-1/4 in. (362 mm)
    • Net Weight: 40i w/torch: 31.4 lb (14.2 kg)
    • Ship weight: 35.8 lb (16.2 kg)
    Learn More
  2. Hobart Welder Ironman 230 Mig 500536

    Hobart Welder Ironman 230 Mig 500536


    The IronMan™ 230 is a total redesign of the full-size MIG platform, outperforming the competition on arc quality, voltage control, duty cycle and value. It delivers 30-250 amps of pure power in a heavy duty cabinet. The arc of the new IronMan™ 230 is optimized to deliver a flawless weld, making spatter and post-weld cleanup almost non-existent. The IronMan™ 230 easily runs aluminum – just add the optional Hobart DP-3545-20 spool gun and you’re ready to weld aluminum from 18 gauge to 1/2".

    For improved feedability with aluminum wires or for extended reach with other wires add the Hobart 3545-20 spool gun with its 20 ft. cable length.


    • Welds 24 gauge up to 1/2 inch material in a single pass
    • Excellent aluminum welding with optional Hobart DP-3545-20 spool gun, also provides extended reach with other wires
    • Twelve-tap voltage control allows for a smooth easy-to-control arc
    • Infinite wire feed speed control for precise adjustment of penetration and weld bead shape
    • Comes complete with 200 amp gun and built-in running gear/cylinder rack
    • Unique spool hub makes changing from 2, 10, 33 and 45 lb. wires spools a snap with a tool-less brake tension knob and automatic wire alignment
    • Built-in thermal overload protects the unit
    • Reversible drive rolls: two grooves for two wire sizes on one drive roll. Decreases spare parts and changeover time
    • Hinged door for easy access to wire drive system for spool and drive roll changes
    • Aluminum wire drive system delivers 0 – 700 IPM wire feed speed

    Comes with:

    • 15 ft. (4.6 m), 200 amp MIG gun
    • Regulator/flowmeter
    • 5 ft. (1.5 m) gas hose with fitting
    • 10 ft. (3 m) primary input cable with plug
    • 10 ft. (3 m) work cable with clamp
    • .030/.035 in. dual groove drive roll
    • Extra contact tips
    • Built-in running gear/cylinder rack
    • Weld set-up and parts information chart

    Material Thickness: Welds 24 gauge up to 1/2 inch


    • Maintenance
    • Construction
    • Auto Body
    • Farm/Ranch
    • Rental
    • Home


    • Rated Output at 60% Duty Cycle: 175 A at 25.5 VDC
    • Current Range: 30 - 250 A
    • Max. Open-Circuit Voltage: 35 V
    • Wire Feed Speed Range: 0 - 700 IPM
    • Amps Input at Rated Load, 60 Hz:
      • 200 V - 37
      • 230 V - 32.5
      • kVA - 7.4
      • kW - 6.3
    • Dimensions:
      • H: 31 ½ in. (800 mm)
      • W: 18 7/8 in (479 mm)
      • D: 36 1/2 in (927 mm)
    • Net Weight: 185 lb (84 kg)
    Learn More
  3. Hobart Champion Elite DC Welder/11,000 Watt AC Generator 500562

    Hobart Champion Elite DC Welder/11,000 Watt AC Generator 500562


    Designed to be a jobsite workhorse, the Hobart Champion ELITE combines an 11,000 watt generator with a DC welder for general construction and emergency power applications. It features a rugged, fully enclosed case which provides a protective barrier and lowers noise. All receptacles on the ELITE feature push-button reset circuit breakers. Auxiliary power while welding gives you the capability to run other equipment (lights, grinders) at the same time you are welding. With the quick set current control, it is easy to set up, provides smooth arc starts and maintains optimum arc characteristics. Cables sold separately. 


    • DC weld output for smooth arc performance and easy starts
    • Four 120 volt GFCI (20 amp), one 240V (50 amp) and one 120/240 volt (50 amp) receptacles with push-button reset circuit breakers
    • Auxiliary power while welding gives you the capability to run other equipment (lights, grinder) at the same time you are welding
    • Heavy-duty construction with 100% duty cycle, fully-enclosed engine design, large battery, rugged electrical connections and wiring
    • Just under 4 ft long and weighs less than competitive units
    • "No tools" oil change and standard hour meter to help maintain routine scheduled oil servicing
    • Quick set current control - easy to set up and start welding.
    • Auto-idle for greater fuel savings and reduced noise.
    • Kohler 23 HP gasoline engine, 3600 RPM
    • Fuel-efficient, low-maintenance, twin-cylinder, 4-cycle, overhead-valve
    • 12 gallon fuel tank for extended run time
    Processes: Stick (SMAW)

    Skill Level: Moderate 


    • Maintenance
    • Construction
    • Farm/Ranch
    • Rental
    • Home


    • Rated Output at 25V:
      • 225 A at 100% Duty Cycle 
    • Max. Open-Circuit Voltage: 80
    • Welding Amperage Range:
      • 40 - 225 A DC
    • Single-Phase Generator Power: 11,000 W (10 kVa/kW), 60 Hz, 120/240 Vac; 9500 watts continuous while not welding
    • Dimensions:
      • H: 28 in (711 mm)
      • W: 20 in (508 mm)
      • D: 41 in (1041 mm)
    • Net Weight: Kohler: 490 lb (222 kg)

    Customer would be required to pay for the liftgate service, if needed on the shipping costs.

    Learn More
  4. Hobart EZ Tig 165i Inverter Based Welder 500551

    Hobart EZ Tig 165i Inverter Based Welder 500551


    The EZ-TIG 165i is a complete 230V AC/DC welding package that offers a unique single knob control making it the quickest and easiest AC/DC TIG welder to set up and use. Just plug it into 230 VAC, connect the gas, select the material and thickness, and you are ready to weld. It has superior weld performance from 22 gauge to 3/16 in. (.81 mm to 4.8 mm) in both AC (aluminum) and DC (steel/stainless steel/chromoly). The EZ-TIG 165i is a light weight inverter-based design that includes a foot control.


    • EZ to use interface with one knob and one switch control
    • AC output for superior aluminum welding, DC output for mild and stainless steel
    • Fan-On-Demand to only have the fan run when needed reducing dust/debris being pulled into the unit
    • Infinite amperage control for broader operating range with finer control
    • Inverter-based power source provides a more consistent welding arc while using less power
    • Weighs only 50 lb. (23 kg) so it's EZ to take anywhere
    • HF start to allow for a non-contact arc start to eliminate tungsten and material contamination
    • Auto-postflow to provide optimum shielding based on welding amperage without waste or need for adjustment
    • Automatic high temperature shutdown


    Comes complete with:

    • Inverter based power source with primary cord and plug attached
    • 12.5 ft (3.8 m) Legacy 17 Weldcraft TIG torch
    • Foot-operated control using the RFCS-RJ45 Remote Foot Control
    • 12 ft. (3.7 m) work cable with clamp
    • Regulator/flow gauge with hose
    • Gas regulator, flowmeter and shielding gas hose


    • CC
    • AC/DC
    • 1 Phase

    Material Thickness: Welds 22 gauge to 3/16 inch in both AC (aluminum) and DC (steel/stainless steel/chromoly).

    Skill Level: High


    • Auto Body Repair
    • Auto Body Fabrication
    • Home Hobby
    • Metal Art
    • Vocational Training
    • Signs


    • Rated Output at 20% Duty Cycle:
      • 150 A at 16 VAC
      • 150 A at 16 VDC
    • Welding Amperage Ranges AC/DC: 10 - 165A
    • Max. Open-Circuit Voltage: 80 V
    • Amps Input at Rated Output:
      • AC-230V: 21A
      • DC-230V: 23A
    • Dimensions:
      • H: 17 in (433 mm)
      • W: 9 7/8 in (251 mm)
      • D: 23 7/8 in (608 mm)
    • Net Weight: 50 lb (23 kg)
    Learn More
  5. Hobart Airforce 27i Plasma Cutter 500565

    Hobart Airforce 27i Plasma Cutter 500565


    The Hobart AirForce 27i Plasma Cutter with 16ft Torch (500565) is an economical plasma cutting system for all conductive metals. Inverter-based design and reliable technology pack a lot of performance into a very portable package. This power source adapts to your work site by operating from either 115 or 230 VAC power through standard household outlet using the Multi-Voltage Plug (MVP). Cut faster and more precise than Oxy Fuel. Thanks to a smaller heat-affected zone you have less warping as well.

    • New Inverter Design - Powerful cutting ability at half the weight of prior model (AirForce 400). Weighs only 27.8 lbs.
    • Capable with Engine-Driven Welders - Complete cutting capability when powered by an engine-driven welder with a 240 V generator power outletof 6 kW or more.
    • New Ergonomic Torch - The new HP-50 torch is designed for increased comfort, more efficient cooling and economical replacement cutting tips.
    • Multi-Voltage Plug (MVP) - Allows you to connect to common 120 or 230 V power receptacles without the use of any tools - simply choose the plug that fits the receptacle
    • Post-flow Air Cooling - Cools the torch and tip after cutting, extending life of replaceable tip and electrode.
    • Fan-On-Demand - Runs only when needed reducing dust/debris pulled into unit.
    • Wind Tunnel Technology - Prevents abrasive dust and particles from damaging internal components.
    • Thermal Overload Protection - Built to withstand tough working environments. Rated for 35% duty cycle at 104° Fahrenheit. Duty cycle will increase as environmental temperature decreases.
    • Cable Management Strap - Secures torch, work cable and power cord to make transporting easy and convenient.
    • Line Voltage Compensation (LVC) - Provides peak performance power under variable input voltage conditions (±15%) for steady and cleaner ending cuts.
    • Power Factor Correction - Expands operator’s work area via extension cords while minimizing nuisance trips caused by voltage drops.

    Comes with:

    • HP-50 torch with 16.5 ft (5 m) lead and consumables
    • 16.5 ft (5 m) heavy duty work clamp
    • 10 ft (3 m) power cord with 115/230 VAC, 20 A MVP plug

    Input Power:

    • 115 VAC, 20 amp circuit, single phase
    • 115 VAC, 15 amp circuit, single phase
    • 230 VAC, 50 amp circuit, single phase


    • Sheet Metal
    • HVAC
    • Auto Body
    • Farm/Ranch
    • Plumbing
    Learn More
  6. Hobart Champion 145 Welder/Generator 500563

    Hobart Champion 145 Welder/Generator 500563


    Now with in-use covers and a lower profile!


    • 40 - 145 Amps DC (stick) weld output
    • 30% duty cycle @ 130 Amps
    • 4,500 watts peak, 4,000 watts continuous power
    • Large pancake-style muffler for quiet operation
    • Sight gauge for fuel level
    • 6.25 gallon fuel tank
    • Briggs 10 HP OHV engine - 3 year mfg warranty
    • Covered receptacle package that includes:
      • (1) 6-50R 240V receptacle - directly plug in your Hobart 230V equipment
      • (2) 115V 20 Amp Duplex GFCI receptacles
    • Includes running gear


    • Mild Steel
    • Stainless Steel
    • Cast Iron

    The Champion 145 beats the competition by having:

    • Wider output range - 40-145 amps
    • Stronger duty cycle - 30% duty cycle @ 130 amps
    • Four 20A, 120 VAC GFCI  receptacles
    • Smaller and lighter package
    • Running gear included for superior portability
    Learn More

6 Item(s)

per page

Grid List

Set Ascending Direction